Putting two audio files back to back is easy. Making them sound like one recording is the harder part. A voice memo recorded on a phone, a clip from a laptop microphone and a song intro will all have different loudness, different background noise and sometimes different formats. This guide covers what to do before and after pressing join in the Audio Joiner, so the listener does not reach for the volume knob halfway through.
What the joiner does, and what it does not
The files are decoded by your browser, placed one after another in the order shown in the list, and encoded as one file. There is no gap and no crossfade between parts, and nothing is trimmed or levelled for you. That keeps the tool predictable, but it means every problem in your source files is carried over into the result. The joined file also uses the sample rate of the first file, so it is sensible to put the best-quality file first. Parts with fewer channels are copied to the missing ones, so a mono voice memo joined with a stereo song plays from both speakers.
Step 1: trim each part first
Most ugly joins are caused by the ends of the parts, not by the joiner. A part that ends with a loud breath, a click or two seconds of silence will sound the same after the join. Trim the ends of each file with the Audio Cutter, ending each part in a natural pause. If the parts are voice memos, a short pause of room tone at each end sounds more natural than a hard stop.
Step 2: even out the loudness
Play the end of one file and the start of the next at the same system volume. If one is clearly louder, the listener will hear the jump. There are two ways to deal with it:
- Normalize each file to the same target with Normalize Audio. It measures how loud each file actually sounds and changes each by the amount needed to reach one target, so the parts match. This is the best option when you have many files.
- Boost only the quiet one with the Volume Booster. This is quicker when exactly one part is too quiet, but you choose the amount by ear.
Do this before joining, not after. If you normalize the finished file, the loud part and the quiet part are still different from each other; they just move up or down together.
Step 3: add the files and set the order
- Drop all the files together, or add them one by one with the add button. The list shows each file with its duration.
- Drag a row, or use the up and down buttons, until the order is right. Remove any file you do not need.
- Press Preview joined and listen to the whole thing at least once, paying attention to each join.
- Choose the output format and press the join button. The button stays disabled until there are at least two files.
Which output format
| Situation | Choose | Why |
|---|---|---|
| The joined file is the final product to send or upload | MP3 (192 kbps) | Small and plays everywhere |
| You will edit the result again, for example cut or normalize it | WAV (lossless) | Avoids compressing the audio twice |
| Parts came from different formats, such as M4A and WAV | Either; check the preview | Everything is converted to the same output anyway |
A WAV file is much larger than an MP3 of the same length, so do not choose WAV just to be safe if you only want to email the result.
Problems you can run into
- One part is mono and the others are stereo. The result has as many channels as the widest file, and a mono part is played from both sides, so it sounds centred. That is usually what you want; if one part sounds odd, check it alone in the preview first.
- One file is rejected. The browser could not decode it. Convert it to MP3 or WAV first. If it comes from a video, take the sound out with Video to Audio.
- The page runs out of memory or becomes slow. Decoded audio is large: a few minutes of stereo sound takes tens of megabytes. Join fewer files at a time and then join the results, and prefer a computer over a phone for long material.
- You hear a click at a join. The previous part ended mid-wave. Go back to the cutter and end it in a quiet spot.
- Background noise changes suddenly at a join. That is the different rooms the files were recorded in. Run each file through Remove Background Noise with the same settings before joining.
Joining versus mixing
This tool puts files one after another. It cannot play two files at the same time, so it will not lay music under a voice or add a sound effect over a recording. If you need layers, you need a multi-track editor. If you want a recording with music before and after it, the joiner is exactly right: add the intro, the recording and the outro in that order.
Frequently asked questions
How many files can I join?
There is no fixed number in the tool. The practical limit is the memory of your device, because all files are decoded at once.
Will the quality drop when I join?
With WAV output the samples are kept as decoded. With MP3 output the joined audio is compressed at 192 kbps once. Starting from already compressed files means they have been compressed before, which cannot be undone.
Can I change the order after previewing?
Yes. Reorder the list and preview again before you join.
Are my files uploaded?
No. Decoding, joining and encoding happen in your browser.