Skip to content
TabShedKitsMy desk

Cut Audio Without Clicks or Pops at the Edges

Updated 5 min readBy

Why a trimmed audio clip starts or ends with a click, and how to place the start and end points so the cut sounds clean.

Audio CutterCut and trim audio files
Open Audio Cutter
On this page
  1. Why cuts click
  2. Choose quiet places, not loud ones
  3. Where exactly to cut
  4. Check the edges before you download
  5. MP3 or WAV for the export
  6. Common problems
  7. When this tool is not the right one
  8. Frequently asked questions

You trim a voice memo, play the result, and the first half second has a sharp tick, or the clip stops with a pop. Nothing is wrong with the file. The cut simply landed in the middle of a sound wave. This guide explains why that happens and how to place the start and end in the Audio Cutter so the clip sounds clean.

Why cuts click

Digital audio is a long list of numbers, one for every fraction of a millisecond, describing how far the speaker cone should be pushed in or out. A smooth sound moves up and down around a middle line. If your cut starts at a moment when the wave is far from the middle, the speaker has to jump from silence to that position instantly. That jump is the click. The same happens at the end, when the sound is stopped while the wave is still away from the middle.

The Audio Cutter does not add fades, so the quality of the edges depends on where you put the start and the end. You cannot fix a bad edge afterwards inside the tool; you choose better points and cut again.

Choose quiet places, not loud ones

The safest cut points are small gaps in the sound: the breath between two sentences, the silence before a drum hit, the pause between two notes. In the waveform, these look like flat, thin stretches between taller blocks.

  1. Open the tool and drop your file. The waveform appears once the browser has decoded it.
  2. Click the waveform near where you want the clip to begin. Hold Shift and click near where it should end.
  3. Press Play selection and listen to the first and last second. This is the whole test: if you hear a tick, move the point.
  4. Type small corrections into the Start (seconds) and End (seconds) boxes. Moving by a tenth of a second at a time is enough to find a quiet spot.
  5. When both edges sound clean, choose the output format and download.

Where exactly to cut

MaterialStart pointEnd point
SpeechIn the pause just before the first word, with a little room tone left inAfter the last word has fully decayed, in the breath or silence that follows
Music with a beatJust before a beat, in the tail of the previous oneRight after a note has died away, or just before the next beat
Sustained notes or ambient soundWhere the sound is at its quietestWhere the sound is at its quietest; avoid cutting a held note
Phone recordings with background noiseAny moment where nobody is speakingSame; the noise floor is steady, so the join is not audible

For a ringtone or an alarm tone, start the clip slightly before the first sound rather than exactly on it. A few hundredths of a second of silence cost nothing, and they protect you from a clipped first note.

Check the edges before you download

The preview plays the selection from memory, exactly the samples that will be exported. Listen with headphones, because laptop speakers hide small clicks. Listen twice: once to the start and once to the end. If the clip will loop, as many ringtones and game sounds do, check the join between the end and the start as well by playing the selection twice in a row.

MP3 or WAV for the export

The tool exports either an MP3 at 192 kbps or a lossless WAV. The audio is decoded and encoded again when you download, so an MP3 saved as MP3 is compressed a second time. For a one-off clip that you will send or play, MP3 is fine. If you plan more edits, such as joining several clips or normalizing their loudness, save the pieces as WAV and make an MP3 only at the very end. The Selection card shows the length of the clip and a WAV size estimate; a WAV export larger than 500 MB is refused, so cut a shorter section if you reach that limit.

Common problems

  • The clip still clicks after you moved the point. Zoom out mentally: the click may come from a loud sound that starts right at the edge. Move the start earlier, into a clearly flat stretch.
  • The start sounds clipped. You began on the first syllable. Move the start back a tenth of a second or two.
  • The sound is much quieter than expected. Cutting does not change volume. Raise it with the Volume Booster.
  • The page cannot load the file. The browser cannot decode that format. Convert it to MP3 or WAV in another app first. If the audio is inside a video, extract it with Video to Audio, then cut the result.
  • You need several clips from one file. The tool exports one selection at a time. Cut each part separately and join them later if needed.

When this tool is not the right one

If you need a smooth fade in or out, a crossfade between two clips, or a cut that follows a visible spectrogram, a full audio editor on your computer is a better choice. The Audio Cutter is for the quick job: pick a section, check that the edges sound right, and save it. A very long recording is decoded entirely into memory, so a phone may struggle with hour-long files; the tool also refuses a selection longer than one hour.

Frequently asked questions

Does cutting change the quality of the part I keep?

The samples inside your selection are kept as they are. Quality only changes if you export to MP3, which compresses the audio again. Choose WAV to avoid that.

What is the shortest clip I can export?

The selection must be at least 0.1 seconds long, and the end must come after the start.

Is my file uploaded?

No. The file is decoded and cut in your browser and never leaves your device.

Can I cut a part out of the middle and keep both sides?

Not in one step. Export the part before the gap and the part after it as two files, then put them together with the Audio Joiner.