Skip to content

Make a quiet recording louder before you send it

A quiet voice note or recording, made loud enough without crackle.

You recorded a lecture from the back of the room, a voice message on a noisy street or an interview on a laptop microphone, and the person who receives it has to turn everything up to the maximum to hear. Then the next message arrives at normal volume and nearly takes their ears off. A recording that is too quiet is a small problem. A recording that has been boosted badly is a worse one.

This template raises the level in a controlled way. The first step is to listen and find out where it is quiet, because a recording that is quiet only in places needs a different fix from one that is quiet everywhere. Then the file is boosted with a preview that shows where it would distort. An optional step evens out the loudness so it matches what people expect from other audio. The last step is to listen at low volume, which is where harshness shows up.

Use it now

5 tasks, in the order you do them. Tasks with a tool open it with the job's files and tick themselves when you save the result.

  1. 1Listen to the original and note where it is too quiet
  2. 2Raise the volumeVolume Booster
  3. 3Even out the loudness (optional)Audio Normalizer
  4. 4Listen to the result at a low volume
  5. 5Send it
Makes this job on your desk, on this device. No account.

Step by step, and why the defaults are what they are

1. Listen to the original and note the quiet parts

Play the file once through and write in the job note whether it is quiet throughout, or only in places, for example when one person speaks softly.

Why this default. Boosting multiplies the whole file by one number. That helps a recording that is evenly quiet. It does not fix a quiet speaker next to a loud one, because the loud part reaches its limit first.

2. Raise the volume

Open the Volume Booster and add the file. The slider goes up to 500%, and most files sound right in the range of 150% to 200%. For a very quiet recording, switch Normalize on first. Watch the waveform: red marks show where the sound reaches the maximum and may distort.

Why this default. The tool applies a soft limiter that rounds off peaks rather than cutting them flat, which sounds smoother than hard clipping. The red marks are your honest feedback: when they cover most of the waveform, you are asking for too much and should lower the gain. Open Volume Booster.

3. Even out the loudness (optional)

Run the Audio Normalizer when the recording will sit next to other audio, such as a podcast episode or a playlist. Choose −16 LUFS for speech and podcasts, or −14 LUFS for music and video on streaming services.

Why this default. Normalizing measures how loud the file sounds to a person and moves it by the amount needed to hit a target, instead of multiplying by a number you guess. It is the step that makes two recordings from different days sound equally loud. Open Audio Normalizer.

4. Listen to the result at a low volume

Turn your playback volume down before you press play. Listen for crackle on the loud words and for a hiss that grew with the boost.

Why this default. At low volume, distortion and noise stand out more than at high volume, where they blend with everything else. It also protects your ears from a mistake in the settings.

Variants

The recording is a video

Pull the sound out with Video to Audio, boost it here and send the audio, or keep the video and tell the other person the sound is in a separate file.

Lots of background hiss

Boosting raises the noise as well as the voice. Run Remove Background Noise first, then boost the cleaned file.

Several clips of different loudness

Use the Audio Normalizer on the whole set with one target, so every clip comes out at the same level.

Common problems

The boosted file crackles.

The gain is too high for the loudest parts. Lower the slider until the red marks mostly disappear, or normalize first and use a smaller boost.

Only one part is quiet.

A single gain value cannot fix it. Cut that part out with Audio Cutter, boost it alone and join the pieces with Audio Joiner.

MP3 or WAV?

MP3 is smaller and works everywhere, and WAV keeps every detail but is much bigger. Send MP3 unless the other person needs to edit the audio.

Questions

Is my recording uploaded?

No. The audio is decoded, boosted and encoded inside your browser and never leaves your device.

Can I make it louder than 500%?

Not in one step, and you rarely should. If a file needs more than that, it is probably too quiet to rescue well, and a re-recording is the better fix.

Does the original stay?

Yes. The job keeps it as the first version, and the boosted file is saved as a new version next to it.

More in the Send & submit kit

About the Send & submit kit · How TabShed works