Skip to content
TabShedKitsMy desk

How to Put Readable Text on a Busy Photo

Updated 6 min readBy

Why caption text disappears on a photo and how to fix it with outline, shadow, size and placement in TabShed's Add Text to Image tool.

Add Text to ImagePut text and captions on photos
Open Add Text to Image
On this page
  1. Start with the basic setup
  2. Step 1: choose a size that matches the picture, not the screen
  3. Step 2: add an outline before you touch the color
  4. Step 3: use shadow for softness, not as a rescue
  5. Step 4: place the text where the photo is quiet
  6. Controls and what they are good for
  7. Using more than one text layer
  8. Common problems
  9. When this tool is not the right one
  10. FAQ

You add a caption to a holiday photo, look at it on your phone, and the words melt into the sky. The text is there, but nobody can read it. This is the most common problem with text on pictures, and it is almost never about the font. It comes from low contrast between the letters and whatever sits behind them. This guide shows how to fix it with the controls in the Add Text to Image tool, in the order that usually solves it fastest.

Start with the basic setup

  1. Open the tool and drop in a JPG, PNG, GIF or WebP file. The limit is 25 MB. Everything runs in your browser, so the picture is not uploaded.
  2. The first text layer is created for you with the default font (Arial), bold, at size 48. Type your words into the Text box.
  3. Click on the image to place the text, or drag it. You can also type exact numbers into Position X and Position Y.
  4. Press Apply text. A result preview appears. If you want to change something, press Apply text again and then download the PNG.

The preview is the original image with your text layers drawn on top at full resolution, so a 4000-pixel-wide photo gets 4000-pixel-wide text. That matters for sizes, as you will see next.

Step 1: choose a size that matches the picture, not the screen

Font size goes up to 200, and it is measured in pixels of the real image. A size of 48 looks big on a 600-pixel-wide image and tiny on a 4000-pixel-wide photo. If your text looks too small, do not nudge the slider by two or three points. Think in proportion: a headline usually needs to be somewhere around a twentieth of the image width or more to survive being shrunk to a phone screen. Preview the result at the size people will actually see it, not full screen on a monitor.

Step 2: add an outline before you touch the color

Under Effects there is a Stroke width (0 to 10) with its own color picker. A stroke draws a border around every letter. A white word with a thin dark stroke can sit on a light sky, a dark wall and a face, because wherever the letter blends in, the outline separates it. The rule that works: pick a fill color and a stroke color that are far apart in brightness, such as white and near-black. Start at a stroke of 2 or 3 and raise it only if the edges still look soft. Very thick strokes make small text look clumsy because the outline eats into the letter shape.

Step 3: use shadow for softness, not as a rescue

Shadow blur goes from 0 to 20 and also has a color. A soft dark shadow lifts text off the photo gently, which suits photography and calm images. A shadow alone is weaker than a stroke on very busy backgrounds, because it fades out. Use both together on difficult photos: a small stroke for edge definition and a modest shadow for depth. If the text starts to look like a cheap effect, remove one of them rather than increasing both.

Step 4: place the text where the photo is quiet

Every photo has calm areas: sky, a wall, blurred background, a table surface. Put the text there. Moving a caption fifty pixels often does more than any style change. Avoid placing words over faces, over high-detail patterns, and across the horizon line where brightness changes suddenly, because one half of the word may be readable and the other half lost.

Controls and what they are good for

ControlRange or choicesUse it to
Font sizeUp to 200 pxMake the text proportional to the image
OpacityUp to 100Soften a secondary line; keep main text at full opacity
Bold / ItalicToggle buttonsBold helps small text; italic suits quotes
Text alignLeft, center, rightLine the text up with the side you placed it on
RotationUp to 180 degreesAngled labels, stamps, vertical text
Stroke width0 to 10Separate letters from the background
Shadow blur0 to 20Add depth and soften edges

Using more than one text layer

You can add several layers; each one has its own text, font, color, position and effects, and the list under Text layers lets you switch between them or remove one. A common pattern is a large title layer plus a smaller one underneath. Make the two clearly different in size, not slightly different, so the hierarchy is obvious. Keep to one or two fonts in total. Mixing four fonts on one photo makes the caption look like a ransom note and is harder to read than a single plain line.

Common problems

  • The text looks blurry in the result. The text is drawn into the image at its real pixel size, so blur usually means the source photo is small and is being viewed enlarged. Start from a bigger picture.
  • My file is a JPG but the download is a PNG. The finished image is always saved as PNG. If the size matters for email or a website, run it through the Image Compressor afterwards and choose WebP or a lower quality.
  • I cannot select the file. Files above 25 MB are refused, as are anything that is not an image. Resize first with the Image Resizer.
  • Text is cut off at the edge. Check Position X and Y and reduce the font size; for a long caption, shorten it or put the second line in its own text layer.

When this tool is not the right one

If you want to repeat a name or logo across a whole photo to discourage reuse, the Image Watermark tool is built for that, with position and opacity presets. If you are designing a large cover image with a layout, stickers and borders, the Thumbnail Generator gives you a ready 16:9 canvas. This tool is best for plain captions, quotes, labels and dates on a single image.

FAQ

Can I use any font on my computer?

No. The Font list contains a fixed set of web-safe families. Pick from that list.

Can I save the layers to edit later?

No. The download is a flat PNG. Keep your original photo and redo the text if you need to change it.

Will the picture be uploaded?

No. The text is drawn in the browser and the file stays on your device.

What color should the text be?

White with a dark outline works on most photos. If the area behind the text is very bright, switch to dark text with a light outline. Check the choice with the Color Contrast Checker if the caption is important.